SELF CONTAINED COOLING UNIT 2/5 TON 4200VEX #36747

• CellarPro 4200VEx units are self-enclosed, fully-charged units designed to be installed through-the-wall and sized to fit in between standard wall studs.
• For convenience and access, we offer a remote control display kit which is wired to the cooling unit and allows the digital display to be mounted inside or outside the cellar.
• 4200VEx units require fresh air intake at the rear of the cooling unit. 
• 4200VEx units include our Compressor Heater (P/N 1727) as standard equipment, allowing exposure to temperatures down to 20F.
• For installation in environments below 20F down to -20F, we recommend our Fan-Cycling Switch (P/N 6972) combined with our compressor heater.
• The front of the cooling unit should never be exposed to temperatures below 32F.
• A CellarPro cooling unit must always be used in the upright position, and should never be operated on its side or upside down.
• We ship these units strapped to a pallet via common carrier with curbside delivery. Inside delivery is available for an additional charge.

CellarPro engineered the 4200VEx cooling unit to provide maximum cooling power and adjustable humidity control for cellars up to 1,000 cubic feet. Our VE Series cooling units offer savings of $1000, with the same cooling power but with fewer features, as compared to our VS Series!

Designed for external installations, 4200VEx units are built with high-output Secop compressors and oversized coils for maximum performance in high-temperature environments up to 110F. 

All air-cooled refrigeration equipment requires fresh air intake to dissipate the heat generated by the cooling unit. The fresh air intake CANNOT come from the wine cellar space – it must come from space outside the cellar. 

• Designed to operate in extreme temperature conditions (20F to 110F). 
• Dual high-output centrifugal fans provide maximum cooling power and performance 
• High-output compressor and extra-large coils are balanced to maintain recommended humidity inside your cellar
• Commercial-grade Electrofin coating protects the evaporator coils from leaks and corrosion.
• Excess condensate is managed with a 1/2″ drain line 
• Intuitive LED display panel mounted on the evaporator with a digital programmable thermostat is simple and easy to use. The remote thermostat is available as an upgrade.
• Energy-saver mode, quick-chill mode, and auto-defrost cycle provide convenient solutions to everyday cellar needs.
• Temperature set point range is 47F to 62F when the cooling unit is appropriately sized.
• Unit operates with minimal vibrations and noise 
• Audible and visual alarms and maintenance-needed indicators protect the cooling unit and the wine cellar.
• A common, dedicated 15-amp circuit is required to power the unit.
• With dual power sources and a 10-foot power cord, the unit can be plugged into a receptacle from either the front or the rear of the cooling unit, providing flexibility for most installations.
• Easy-access port for biocide tablets to prevent mold growth in the drain system 
• Adjustable mounting brackets, included as standard equipment, ensure easy installation.
• Removable steel case and refrigerant access valve provide access to the internal components for servicing and repair.
• CellarPro’s 5-Year Standard Warranty, the most thorough in the industry, protects the unit against manufacturing defects.
• Compatible with easy-access aluminum air filter (sold separately)
• Fan cycling switch (sold separately) allows the unit to operate in temps down to -20F
• An optional Extended Warranty (P/N 1836) is available for additional protection.
• ETL Tested and Certified to rigorous UL Standards for safety.

3938 SENSIBLE BTUH @ 55F. 
Priced affordably with essential features, CellarPro’s 4200VEx cooling units (2/5 Ton Nominal) are engineered for wine cellars up to 1,000* cubic feet in both commercial and residential wine cellars.

Performance testing shows that this unit maintains optimal cellar temperature and humidity in extreme temperatures up to 110F.

The BTU/h value shown here is a theoretical number. There are often circumstances under which a cellar design may require a larger unit due to variables not accounted for in the formula. For example, these variables could be building materials (such as glass, stone, concrete, etc.)

Which do not offer the insulation capacity required to maintain the optimal cellar environment. We recommend purchasing a unit with a larger capacity to compensate for these unaccounted-for variables. An undersized unit can lead to premature failure and will most likely prevent the cellar from reaching your desired temperature.

Brand: CellarPro  

UPC: 077757367472 

Size: 14 1/4w x 26 7/8d x 19 3/4h (in)  

Weight: 103 lbs  

Power/Rating: 
115V AC / 60 Hz  
Compressor Amps:  
– Common dedicated 15-amp circuit is required to power the unit.  
– Startup: 42.0 Amps  
– Unit Amp Rating: 10.1 Amps  
– Total Watts: 730 Watts   

BTUH @ 55F / Decibels:
– 3938 / 67 dBA  
– 2/5 Ton Nominal  

Cold Temperature

• Compressor Heater #1727: protects the unit when installed in environments that drop below 40F down to 20F.
• Fan Cycling Switch #6972: supports the unit in temperatures below 20F and as low as -20F when combined with our compressor heater.

Hoods

• Duct Hood (Hot Side)#7407 and Kit #1113: allows you to install the unit completely inside your cellar or in a small space with limited airflow, up to 100 equivalent feet (50 feet per duct) using 8″ diameter ducting.
• Duct Kits are the same as Duct Hoods, and also include 2 x 25-feet of 8-inch insulated (R-6) flex ducting.

Extended Mounting Bracket

• For retrofit installations where the wall opening is too big for our cooling unit, use our Extended Mounting Bracket on one or both sides to plug the opening.

Filters & Grills

• Use our filter & grill guide to find the cooling unit filter or duct filter and/or duct grill that is appropriate for your cooling unit.

Maintenance

• Refer to filter replacements in the previous section.
• Evap Fresh #17984: Should be sprayed on the evaporator (cold-side) coils once a quarter, especially when the evaporator coils frequently have condensation, to extend the life of the evaporator coils and to reduce the growth of mold in the drain pan.
• Condenser Brush #1475: With a long handle and stiff bristles, the brush is ideal for cleaning off the dust and dirt that collect on the hot-side condenser coils, especially when a filter isn’t used on the coils.

Remote Thermostats, Displays & Probes

• Networkable Thermostats #27346 and #27310: connect your cooling unit to a networkable, wi-fi enabled thermostat (sold separately). Must be ordered at the same time that the equipment is ordered. Other limitations apply – read the networkable thermostat description for more information. Includes 10 feet of wiring.
• Remote Display #1603: lets you place the digital panel wherever you want, whether inside or outside the cellar. Includes 10 feet of wiring.
• Bottle Probe #1434: this remote thermostat with a 10-foot cord overrides the thermostat on the face of the cooling unit, and allows it to monitor air or liquid temperatures at various locations inside the cellar.
• Bottle Probe Extension Cords available in 25-foot (#1780) and 50-foot (#1781) lengths.

Warranty Resources
– Warranty Overview
– Optional Extended Warranty (sold separately).

Click on one of the following links for more information: 

• • Spec Sheet
  • Cut Sheet
  • Hot Side – As Ducted
  • Installation Diagrams
  • Framing Diagram
  • Configuration Options
  • Owner’s Manual
  • Product Brochure